View LTM4607IV-PBF_4374401.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

LTM4607 36VIN, 24VOUT High Efficiency Buck-Boost DC/DC Module FEATURES

DESCRIPTION
The LTM(R)4607 is a high efficiency switching mode buckboost power supply. Included in the package are the switching controller, power FETs, and support components. Operating over an input voltage range of 4.5V to 36V, the LTM4607 supports an output voltage range of 0.8V to 24V, set by a resistor. This high efficiency design delivers up to 5A continuous current in boost mode (10A in buck mode). Only the inductor, sense resistor, bulk input and output capacitors are needed to finish the design. The low profile package enables utilization of unused space on the bottom of PC boards for high density point of load regulation. The high switching frequency and current mode architecture enable a very fast transient response to line and load changes without sacrificing stability. The LTM4607 can be frequency synchronized with an external clock to reduce undesirable frequency harmonics. Fault protection features include overvoltage and foldback current protection. The DC/DC ModuleTM is offered in a small thermally enhanced 15mm x 15mm x 2.8mm LGA package. The LTM4607 is Pb-free and RoHS compliant.
, LT, LTC, LTM and Burst Mode are registered trademarks of Linear Technology Corporation. Module is a trademark of Linear Technology Corporation. All other trademarks are the property of their respective owners.
Single Inductor Architecture Allows VIN Above, Below or Equal to VOUT Wide VIN Range: 4.5V to 36V Wide VOUT Range: 0.8V to 24V 5A DC (10A DC in Buck Mode) High Efficiency Up to 98% Current Mode Control Power Good Output Signal Phase-Lockable Fixed Frequency: 200kHz to 400kHz Ultra-Fast Transient Response Current Foldback Protection Output Overvoltage Protection Small, Low Profile Surface Mount LGA Package (15mm x 15mm x 2.8mm)
APPLICATIONS

Telecom, Servers and Networking Equipment Industrial and Automotive Equipment High Power Battery-Operated Devices
TYPICAL APPLICATION
20V/2.5A Buck-Boost DC/DC Module with 4.5V to 36V Input
VIN 4.5V TO 36V 100 CLOCK SYNC 10F 50V ON/OFF VIN RUN PLLIN V OUT FCB 4.7H SW1 SW2 RSENSE SENSE+ 0.1F SS SGND PGND SENSE- VFB 4.12k
4607 TA01
Efficiency and Power Loss vs Input Voltage
6 5 4 3 2 1 VOUT = 20V, 2.5A f = 200kHz 6 11 16 21 VIN (V) 26 31 0 36 POWER LOSS (W) VOUT 20V 2.5A EFFICIENCY (%) 99 98 97 96 95 94 93
LTM4607
10F 35V
+
330F 25V
R2 7m
92 91 90
4607 TA01b
4607f
1
LTM4607 ABSOLUTE MAXIMUM RATINGS
(Note 1)
PIN CONFIGURATION
(See Table 6 Pin Assignment)
TOP VIEW BANK 2
M L
VIN ............................................................. -0.3V to 36V VOUT ............................................................. 0.8V to 25V INTVCC, EXTVCC, RUN, SS, PGOOD .............. -0.3V to 7V SW1, SW2 .................................................... -5V to 36V VFB, COMP ................................................ -0.3V to 2.4V FCB, STBYMD ....................................... -0.3V to INTVCC PLLIN ........................................................ -0.3V to 5.5V PLLFLTR.................................................... -0.3V to 2.7V Operating Temperature Range (Note 2) ...............................................-40C to 85C Junction Temperature ........................................... 125C Storage Temperature Range...................-55C to 125C
BANK 4
K J H G
BANK 1
BANK 3
BANK 5
F E D C
BANK 6
B A 1 2 3 4 5 6 7 8 9 10 11 12
LGA PACKAGE 141-LEAD (15mm x 15mm x 2.8mm)
TJMAX = 125C, JP = 4C/W, WEIGHT = 1.5g
ORDER INFORMATION
LEAD FREE FINISH LTM4607EV#PBF LTM4607IV#PBF PART MARKING* LTM4607V LTM4607V PACKAGE DESCRIPTION 141-Lead (15mm x 15mm x 2.8mm) LGA 141-Lead (15mm x 15mm x 2.8mm) LGA TEMPERATURE RANGE -40C to 85C -40C to 85C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ This product is only offered in trays. For more information go to: http://www.linear.com/packaging/
ELECTRICAL CHARACTERISTICS
SYMBOL Input Specifications VIN(DC) VIN(UVLO) IQ(VIN) Input DC Voltage Undervoltage Lockout Threshold Input Supply Bias Current Normal Standby Shutdown Supply Current PARAMETER
The denotes the specifications which apply over the -40C to 85C temperature range, otherwise specifications are at TA = 25C, VIN = 12V. Per typical application (front page) configuration.
CONDITIONS
MIN 4.5
TYP
MAX 36
UNITS V V mA mA A
VIN Falling
3.4 2.8 1.6 35
4
VRUN = 0V, VSTBYMD > 2V VRUN = 0V, VSTBYMD = Open
60
4607f
2
LTM4607 ELECTRICAL CHARACTERISTICS
SYMBOL IOUTDC PARAMETER Output Specifications Output Continuous Current Range VIN = 32V, VOUT = 12V (See Output Current Derating Curves VIN = 6V, VOUT = 12V for Different VIN, VOUT and TA) Reference Voltage Line Regulation Accuracy Load Regulation Accuracy VIN = 4.5V to 36V, VCOMP = 1.2V (Note 3) VCOMP = 1.2V to 0.7V VCOMP = 1.2V to 1.8V (Note 3) Drain to Source Voltage VDS = 12V, Bias Current ISW = 10mA Drain to Source Voltage VDS = 12V, Bias Current ISW = 10mA Drain to Source Voltage VDS = 12V, Bias Current ISW = 10mA Drain to Source Voltage VDS = 12V, Bias Current ISW = 10mA Drain to Source Voltage VDS = 12V, Bias Current ISW = 10mA Drain to Source Voltage VDS = 12V, Bias Current ISW = 10mA Drain to Source Voltage VDS = 12V, Bias Current ISW = 10mA Drain to Source Voltage VDS = 12V, Bias Current ISW = 10mA Drain to Source Voltage VDS = 12V, Bias Current ISW = 10mA Drain to Source Voltage VDS = 12V, Bias Current ISW = 10mA Drain to Source Voltage VDS = 12V, Bias Current ISW = 10mA Drain to Source Voltage VDS = 12V, Bias Current ISW = 10mA Bias Current ISW = 3A Bias Current ISW = 3A Bias Current ISW = 3A Bias Current ISW = 3A

The denotes the specifications which apply over the -40C to 85C temperature range, otherwise specifications are at TA = 25C, VIN = 12V. Per typical application (front page) configuration.
CONDITIONS MIN TYP 10 5 0.002 0.15 -0.15 50 40 25 20 20 20 50 50 50 50 220 220 10 12 8 8 18 12 12 0.02 0.5 -0.5 MAX UNITS A A % % % ns ns ns ns ns ns ns ns ns ns ns ns m m m m
VFB/VFB(NOM) VFB/VFB(LOAD) Switch Section M1 tr M1 tf M3 tr M3 tf M2, M4 tr M2, M4 tf t1d t2d t3d t4d Mode Transition 1 Mode Transition 2 M1 RDS(ON) M2 RDS(ON) M3 RDS(ON) M4 RDS(ON)
Turn-On Time (Note 4) Turn-Off Time Turn-On Time Turn-Off Time Turn-On Time Turn-Off Time M1 Off to M2 On Delay (Note 4) M2 Off to M1 On Delay M3 Off to M4 On Delay M4 Off to M3 On Delay M2 Off to M4 On Delay M4 Off to M2 On Delay Static Drain-to-Source OnResistance Static Drain-to-Source OnResistance Static Drain-to-Source OnResistance Static Drain-to-Source OnResistance Nominal Frequency Lowest Frequency Highest Frequency PLLIN Input Resistance Phase Detector Output Current
Oscillator and Phase-Locked Loop fNOM fLOW fHIGH RPLLIN IPLLFLTR VPLLFLTR = 1.2V VPLLFLTR = 0V VPLLFLTR = 2.4V fPLLIN < fOSC fPLLIN > fOSC 260 170 340 300 200 400 50 -15 15 330 220 440 kHz kHz kHz k A A
4607f
3
LTM4607 ELECTRICAL CHARACTERISTICS
SYMBOL Control Section VFB VRUN ISS VSTBYMD(START) VSTBYMD(KA) VFCB IFCB VBURST DF(BOOST, MAX) DF(BUCK, MAX) tON(MIN, BUCK) RFBHI INTVCC VLDO/VLDO VEXTVCC VEXTVCC(HYS) VEXTVCC VSENSE(MAX) VSENSE(MIN, BUCK) ISENSE PGOOD VFBH VFBL VFB(HYS) VPGL IPGOOD PGOOD Upper Threshold PGOOD Lower Threshold PGOOD Hysteresis PGOOD Low Voltage PGOOD Leakage Current VFB Rising VFB Falling VFB Returning IPGOOD = 2mA VPGOOD = 5V 5.5 -5.5 7.5 -7.5 2.5 0.2 0.3 1 10 -10 % % % V A Feedback Reference Voltage RUN Pin ON/OFF Threshold Soft-Start Charging Current Start-Up Threshold Keep-Active Power On Threshold Forced Continuous Threshold Forced Continuous Pin Current Burst Inhibit (Constant Frequency) Threshold Maximum Duty Factor Maximum Duty Factor VFCB = 0.85V Measured at FCB Pin % Switch M4 On % Switch M1 On VRUN = 2.2V VSTBYMD Rising VSTBYMD Rising, VRUN = 0V 0.76 -0.3 VCOMP = 1.2V
The denotes the specifications which apply over the -40C to 85C temperature range, otherwise specifications are at TA = 25C, VIN = 12V. Per typical application (front page) configuration.
PARAMETER CONDITIONS MIN 0.792 1 1 0.4 TYP 0.8 1.6 1.7 0.7 1.25 0.8 -0.2 5.3 99 99 200 99.5 VIN > 7V, VEXTVCC = 5V ICC = 0mA to 20mA, VEXTVCC = 5V ICC = 20mA, VEXTVCC Rising ICC = 20mA, VEXTVCC = 6V Boost Mode Buck Mode Discontinuous Mode VSENSE- = VSENSE+ = 0V

MAX 0.808 2.2
UNITS V V A V V
0.84 -0.1 5.5
V A V % %
Minimum On-Time for Synchronous Switch M1 (Note 5) Switch in Buck Operation Resistor Between VOUT and VFB Pins Internal VCC Voltage Internal VCC Load Regulation EXTVCC Switchover Voltage EXTVCC Switchover Hysteresis EXTVCC Switch Drop Voltage Maximum Current Sense Threshold Minimum Current Sense Threshold Sense Pins Total Source Current
250 100.5 6.3 2
ns k V % V mV
100 6 0.3 5.6 300 60 160 -130 -6 -380
Internal VCC Regulator 5.7 5.4
150 190 -150
mV mV mV mV A
Current Sensing Section -95
Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LTM4607E is guaranteed to meet performance specifications from 0C to 85C. Specifications over the -40C to 85C operating temperature range are assured by design, characterization and correlation
with statistical process controls. The LTM4607I is guaranteed over the -40C to 85C temperature range. Note 3: The LTM4607 is tested in a feedback loop that servos VCOMP to a specified voltage and measures the resultant VFB. Note 4: Turn-on and turn-off time are measured using 10% and 90% levels. Transition delay time is measured using 50% levels. Note 5: 100% test at wafer level only.
4607f
4
LTM4607 TYPICAL PERFORMANCE CHARACTERISTICS
Efficiency vs Load Current 6VIN to 12VOUT
100 90 80 70 EFFICIENCY (%) 60 50 40 30 20 10 0 0.01 0.1 1 LOAD CURRENT (A) BURST DCM CCM 10
4607 G01
(Refer to Figure 18) Efficiency vs Load Current 32VIN to 12VOUT
100 90 80 EFFICIENCY (%) 70 60 50 40 30 BURST DCM CCM 20 10 0 0.01 SKIP CYCLE DCM CCM 0.1 1 10 LOAD CURRENT (A) 100
4607 G03
Efficiency vs Load Current 12VIN to 12VOUT
100 90 80 70 EFFICIENCY (%) 60 50 40 30 20 10 0 0.01 0.1 1 LOAD CURRENT (A)
10
4607 G02
Efficiency vs Load Current 3.3H Inductor
100 95 EFFICIENCY (%) 90 85 80 75 70 5VIN TO 5VOUT 12VIN TO 5VOUT 32VIN TO 5VOUT 0 2 4 6 8 LOAD CURRENT (A) 10 12
4607 G04
Efficiency vs Load Current 6H Inductor
100 99 98 97 96 95 94 93 92 91 90 0 2 28VIN to 20VOUT 32VIN to 20VOUT 36VIN to 20VOUT 4 6 LOAD CURRENT (A) 8
4607 G05
Efficiency vs Load Current 8H Inductor
100 99 98 EFFICIENCY (%) 97 96 95 94 93 92 91 90 0 1 28VIN to 24VOUT 32VIN to 24VOUT 36VIN to 24VOUT 3 2 4 5 LOAD CURRENT (A) 6 7
4607 G06
EFFICIENCY (%)
Efficiency vs Load Current
100 95 EFFICIENCY (%) 90 85 80 75 70 0 0.5 5VIN to 16VOUT 5VIN to 20VOUT 5VIN to 24VOUT 1.5 1 2 LOAD CURRENT (A) 2.5 3 VOUT 200mV/DIV IOUT 2A/DIV
Transient Response from 6VIN to 12VOUT
IOUT 2A/DIV
Transient Response from 12VIN to 12VOUT
VOUT 200mV/DIV 200s/DIV
4607 G07
200s/DIV
4607 G08
LOAD STEP: 0A TO 3A AT CCM OUTPUT CAPS: 4x 22F CERAMIC CAPS AND 2x 180F ELECTROLYTIC CAPS 2x 15m SENSING RESISTORS
LOAD STEP: 0A TO 3A AT CCM OUTPUT CAPS: 4x 22F CERAMIC CAPS AND 2x 180F ELECTROLYTIC CAPS 2x 15m SENSING RESISTORS
4607 G06a
4607f
5
LTM4607 TYPICAL PERFORMANCE CHARACTERISTICS
Transient Response from 32VIN to 12VOUT Start-Up with 6VIN to 12VOUT at IOUT = 5A Start-Up with 32VIN to 12VOUT at IOUT = 5A
IOUT 2A/DIV VOUT 100mV/DIV 200s/DIV
4607 G09
IL 5A/DIV IIN 5A/DIV VOUT 10V/DIV 50ms/DIV
4607 G10
IL 5A/DIV IIN 2A/DIV VOUT 10V/DIV 10ms/DIV
4607 G11
LOAD STEP: 0A TO 5A AT CCM OUTPUT CAPS: 4x 22F CERAMIC CAPS AND 2x 180F ELECTROLYTIC CAPS 2x 12m SENSING RESISTORS
0.1F SOFT-START CAP OUTPUT CAPS: 4x 22F CERAMIC CAPS AND 2x 180F ELECTROLYTIC CAPS 2x 12m SENSING RESISTORS
0.1F SOFT-START CAP OUTPUT CAPS: 4x 22F CERAMIC CAPS AND 2x 180F ELECTROLYTIC CAPS 2x 12m SENSING RESISTORS
Short Circuit with 6VIN to 12VOUT at IOUT = 5A
VOUT 5V/DIV
Short Circuit with 32VIN to 12VOUT at IOUT = 5A
Short Circuit with 36VIN to 24VOUT at IOUT = 6A
IIN 2A/DIV VOUT 5V/DIV
VOUT 10V/DIV IIN 2A/DIV
IIN 10A/DIV
20s/DIV
4607 G12
50s/DIV
4607 G13
20s/DIV
4607 G14
OUTPUT CAPS: 4x 22F CERAMIC CAPS AND 2x 180F ELECTROLYTIC CAPS 2x 12m SENSING RESISTORS
OUTPUT CAPS: 4x 22F CERAMIC CAPS AND 2x 180F ELECTROLYTIC CAPS 2x 12m SENSING RESISTORS
OUTPUT CAPS: 4x 22F CERAMIC CAPS AND 2x 180F ELECTROLYTIC CAPS 15m SENSING RESISTORS
4607f
6
LTM4607 PIN FUNCTIONS
VIN (Bank 1): Power Input Pins. Apply input voltage between these pins and PGND pins. Recommend placing input decoupling capacitance directly between VIN pins and PGND pins. VOUT (Bank 5): Power Output Pins. Apply output load between these pins and PGND pins. Recommend placing output decoupling capacitance directly between these pins and PGND pins. PGND (Bank 6): Power Ground Pins for Both Input and Output Returns. SW1, SW2 (Bank 4, Bank 2): Switch Nodes. The power inductor is connected between SW1 and SW2. RSENSE (Bank 3): Sensing Resistor Pin. The sensing resistor is connected from this pin to PGND. SENSE+ (Pin A4): Positive Input to the Current Sense and Reverse Current Detect Comparators. SENSE- (Pin A5): Negative Input to the Current Sense and Reverse Current Detect Comparators. EXTVCC (Pin F6): External VCC Input. When EXTVCC exceeds 5.7V, an internal switch connects this pin to INTVCC and shuts down the internal regulator so that the controller and gate drive power is drawn from EXTVCC. Do not exceed 7V at this pin and ensure that EXTVCC < VIN INTVCC (Pin F5): Internal 6V Regulator Output. This pin is for additional decoupling of the 6V internal regulator. PLLIN (Pin B9): External Clock Synchronization Input to the Phase Detector. This pin is internally terminated to SGND with a 50k resistor. The phase-locked loop will force the rising bottom gate signal of the controller to be synchronized with the rising edge of PLLIN signal. PLLFLTR (Pin B8): The lowpass filter of the phase-locked loop is tied to this pin. This pin can also be used to set the frequency of the internal oscillator with an AC or DC voltage. See the Applications Information section for details. SS (Pin A6): Soft-Start Pin. Soft-start reduces the input surge current from the power source by gradually increasing the controller's current limit. STBYMD (Pin A10): LDO Control Pin. Determines whether the internal LDO remains active when the controller is shut down. See Operations section for details. If the STBYMD pin is pulled to ground, the SS pin is internally pulled to ground to disable start-up and thereby providing a single control pin for turning off the controller. An internal decoupling capacitor is tied to this pin. VFB (Pin B6): The Negative Input of the Error Amplifier. Internally, this pin is connected to VOUT with a 100k precision resistor. Different output voltages can be programmed with an additional resistor between VFB and SGND pins. See the Applications Information section. FCB (Pin A9): Forced Continuous Control Input. The voltage applied to this pin sets the operating mode of the module. When the applied voltage is less than 0.8V, the forced continuous current mode is active in boost operation and the skip cycle mode is active in buck operation. When the pin is tied to INTVCC, the constant frequency discontinuous current mode is active in buck or boost operation. See the Applications Information section. SGND (Pin A7): Signal Ground Pin. This pin connects to PGND at output capacitor point. COMP (Pin B7): Current Control Threshold and Error Amplifier Compensation Point. The current comparator threshold increases with this control voltage. The voltage ranges from 0V to 2.4V. PGOOD (Pin B5): Output Voltage Power Good Indicator. Open drain logic output that is pulled to ground when the output voltage is not within 10% of the regulation point, after a 25s power bad mask timer expires. RUN (Pin A8): Run Control Pin. A voltage below 1.6V will turn off the module. There is a 100k resistor between the RUN pin and SGND in the module. Do not apply more than 6V to this pin. See Applications Information section.
4607f
7
LTM4607 SIMPLIFIED BLOCK DIAGRAM
VIN 4.5V TO 36V EXTVCC M1 INTVCC PGOOD M2 SW1 VOUT 12V 5A CO1 M3 0.1F COMP M4 INT COMP SS SS 0.1F PLLIN INT FILTER PLLFLTR SENSE- RSENSE CONTROLLER RSENSE SENSE+ 100k VFB COUT RFB 7.15k SW2 C1 CIN
L
RUN ON/OFF 100k STBYMD
INT FILTER FCB SGND TO PGND PLANE AS SHOWN IN FIGURE 15 1000pF
PGND
4607 BD
Figure 1. Simplified LTM4607 Block Diagram
DECOUPLING REQUIREMENTS TA = 25C. Use Figure 1 configuration.
SYMBOL CIN COUT PARAMETER External Input Capacitor Requirement (VIN = 4.5V to 36V, VOUT = 12V) External Output Capacitor Requirement (VIN = 4.5V to 36V, VOUT = 12V) CONDITIONS IOUT = 5A IOUT = 5A MIN 10 200 300 TYP MAX UNITS F F
4607f
8
LTM4607 OPERATION
Power Module Description The LTM4607 is a non-isolated buck-boost DC/DC power supply. It can deliver a wide range output voltage from 0.8V to 24V over a wide input range from 4.5V to 36V, by only adding the sensing resistor, inductor and some external input and output capacitors. It provides precisely regulated output voltage programmable via one external resistor. The typical application schematic is shown in Figure 18. The LTM4607 has an integrated current mode buck-boost control, ultralow RDS(ON) FETs with fast switching speed and integrated Schottky diodes. With current mode control and internal feedback loop compensation, the LTM4607 module has sufficient stability margins and good transient performance under a wide range of operating conditions and with a wide range of output capacitors. The frequency of LTM4607 can be operated from 200kHz to 400kHz by setting the voltage on the PLLFLTR pin. Alternatively, its frequency can be synchronized by the input clock signal from the PLLIN pin. The typical switching frequency is 400kHz. The Burst Mode and skip-cycle mode operations can be enabled at light loads in the LTM4607 to improve its efficiency, while the forced continuous mode and discontinuous mode operations are used for constant frequency applications. Foldback current limiting is activated in an overcurrent condition as VFB drops. Internal overvoltage and undervoltage comparators pull the open-drain PGOOD output low if the output feedback voltage exits the 10% window around the regulation point. Pulling the RUN pin below 1.6V forces the controller into its shutdown state. If an external bias supply is applied on the EXTVCC pin, then an efficiency improvement will occur due to the reduced power loss in the internal linear regulator. This is especially true at the higher input voltage range.
APPLICATIONS INFORMATION
The typical LTM4607 application circuit is shown in Figure 18. External component selection is primarily determined by the maximum load current and output voltage. Refer to Table 3 for specific external capacitor requirements for a particular application. Output Voltage Programming The PWM controller has an internal 0.8V1% reference voltage. As shown in the Block Diagram, a 100k 0.5% internal feedback resistor connects VOUT and VFB pins together. Adding a resistor RFB from the VFB pin to the SGND pin programs the output voltage: VOUT = 0.8 V * 100k + RFB RFB Operation Frequency Selection The LTM4607 uses current mode control architecture at constant switching frequency, which is determined by the internal oscillator's capacitor. This internal capacitor is charged by a fixed current plus an additional current that is proportional to the voltage applied to the PLLFLTR pin. The PLLFLTR pin can be grounded to lower the frequency to 200kHz or tied to 2.4V to yield approximately 400kHz. When PLLIN is left open, the PLLFLTR pin goes low, forcing the oscillator to its minimum frequency. A graph for the voltage applied to the PLLFLTR pin vs frequency is given in Figure 2. As the operating frequency increases, the gate charge losses will be higher, thus the efficiency is low. The maximum switching frequency is approximately 400kHz. FREQUENCY SYNCHRONIZATION The LTM4607 can also be synchronized to an external source via the PLLIN pin instead of adjusting the voltage on the PLLFLTR pin directly. The power module has a phase4607f
Table 1. RFB Resistor (0.5%) vs Output Voltage
VOUT RFB VOUT RFB 0.8V Open 9V 9.76k 1.5V 115k 10V 8.66k 2.5V 47.5k 12V 7.15k 3.3V 32.4k 15V 5.62k 5V 19.1k 16V 5.23k 6V 15.4k 20V 4.12k 8V 11k 24V 3.4k
9
LTM4607 APPLICATIONS INFORMATION
locked loop comprised of an internal voltage controlled oscillator and a phase detector. This allows turning on the internal top MOSFET for locking to the rising edge of the external clock. A pulse detection circuit is used to detect a clock on the PLLIN pin to turn on the phase lock loop. The input pulse width of the clock has to be at least 400ns, and 2V in amplitude. The synchronized frequency ranges from 200kHz to 400kHz, corresponding to a DC voltage input from 0V to 2.4V at PLLFLTR. During the start up of the regulator, the phase-lock loop function is disabled.
450 400 OPERATING FREQUENCY (kHz) 350 300 250 200 150 100 50 0 0 1.0 1.5 2.0 0.5 PLLFLTR PIN VOLTAGE (V) 2.5
4607 F02
lower than the preset minimum output current level. The MOSFETs will turn on for several cycles, followed by a variable "sleep" interval depending upon the load current. During buck operation, skip-cycle mode sets a minimum positive inductor current level. In this mode, some cycles will be skipped when the output load current drops below 1% of the maximum designed load in order to maintain the output voltage. When the FCB pin voltage is tied to the INTVCC pin, the controller enters constant frequency discontinuous current mode (DCM). For boost operation, if the output voltage is high enough, the controller can enter the continuous current buck mode for one cycle to discharge inductor current. In the following cycle, the controller will resume DCM boost operation. for buck operation, constant frequency discontinuous current mode is turned on if the preset minimum negative inductor current level is reached. At very light loads, this constant frequency operation is not as efficient as Burst Mode operation or skip-cycle, but does provide low noise, constant frequency operation. Input Capacitors In boost mode, since the input current is continuous, only minimum input capacitors are required. However, the input current is discontinuous in buck mode. So the selection of input capacitor CIN is driven by the need of filtering the input square wave current. For a buck converter, the switching duty-cycle can be estimated as: D= VOUT VIN
Figure 2. Frequency vs PLLFLTR Pin Voltage
Low Current Operation To improve the efficiency at low current operation, LTM4607 provides three modes for both buck and boost operations by accepting a logic input on the FCB pin. Table 2 shows the different operation modes.
Table 2. Different Operating Modes
FCB PIN 0V to 0.75V 0.85V to 5V >5.3V BUCK Force Continuous Mode Skip-Cycle Mode DCM with Constant Freq BOOST Force Continuous Mode Burst Mode Operation DCM with Constant Freq
Without considering the inductor current ripple, the RMS current of the input capacitor can be estimated as: ICIN(RMS) = IOUT(MAX) * D * (1- D)
When the FCB pin voltage is lower than 0.8V, the controller behaves as a continuous, PWM current mode synchronous switching regulator. When the FCB pin voltage is below VINTVCC - 1V, but greater than 0.8V, the controller enters Burst Mode operation in boost operation or enters skipcycle mode in buck operation. During boost operation, Burst Mode operation is activated if the load current is
In the above equation, is the estimated efficiency of the power module. CIN can be a switcher-rated electrolytic aluminum capacitor, OS-CON capacitor or high volume ceramic capacitors. Note the capacitor ripple current rat4607f
10
LTM4607 APPLICATIONS INFORMATION
ings are often based on temperature and hours of life. This makes it advisable to properly derate the input capacitor, or choose a capacitor rated at a higher temperature than required. Always contact the capacitor manufacturer for derating requirements. Output Capacitors In boost mode, the discontinuous current shifts from the input to the output, so the output capacitor COUT must be capable of reducing the output voltage ripple. For boost and buck modes, the steady ripple due to charging and discharging the bulk capacitance is given by: VRIPPLE,BOOST = IOUT(MAX ) * VOUT - VIN(MIN) COUT * VOUT * f VOUT * VIN(MAX ) - VOUT LBUCK where: f is operating frequency, Hz Ripple% is allowable inductor current ripple, % VOUT(MAX) is maximum output voltage, V VIN(MAX) is maximum input voltage, V VOUT is output voltage, V IOUT(MAX) is maximum output load current, A The inductor should have low DC resistance to reduce the I2R losses, and must be able to handle the peak inductor current without saturation. To minimize radiated noise, use a toroid, pot core or shielded bobbin inductor. Please refer to Table 3 for the recommended inductors for different cases. RSENSE Selection and Maximum Output Current RSENSE is chosen based on the required inductor current. Since the maximum inductor valley current at buck mode is much lower than the inductor peak current at boost mode, different sensing resistors are suggested to use in buck and boost modes. The current comparator threshold sets the peak of the inductor current in boost mode and the maximum inductor valley current in buck mode. In boost mode, the allowed maximum average load current is: IOUT(MAX,BOOST) = 160mV RSENSE IL V * IN 2 VOUT ripple IL is typically set to 20% to 40% of the maximum inductor current. In the inductor design, the worst cases in continuous mode are considered as follows: LBOOST VIN * VOUT(MAX ) - VIN
(
)
VOUT(MAX ) * f * IOUT(MAX ) * Ripple% M VOUT * VIN(MAX ) - VOUT
(
)
VIN(MAX ) * f * IOUT(MAX ) * Ripple%
(
)
VRIPPLE,BUCK =
(
)
8 * L * COUT * VIN(MAX ) * f 2
The steady ripple due to the voltage drop across the ESR (effective series resistance) is given by: VESR,BUCK = IL(MAX) * ESR VESR,BOOST = IL(MAX ) * ESR The LTM4607 is designed for low output voltage ripple. The bulk output capacitors defined as COUT are chosen with low enough ESR to meet the output voltage ripple and transient requirements. COUT can be the low ESR tantalum capacitor, the low ESR polymer capacitor or the ceramic capacitor. Multiple capacitors can be placed in parallel to meet the ESR and RMS current handling requirements. The typical capacitance is 300F Additional output filtering may . be required by the system designer, if further reduction of output ripple or dynamic transient spike is required. Table 3 shows a matrix of different output voltages and output capacitors to minimize the voltage droop and overshoot at a current transient. Inductor Selection The inductor is chiefly decided by the required ripple current and the operating frequency. The inductor current
where IL is peak-to-peak inductor ripple current.
4607f
11
LTM4607 APPLICATIONS INFORMATION
In buck mode, the allowed maximum average load current is: IOUT(MAX,BUCK) = 130mV IL + RSENSE 2 The RUN pin can also be used as an undervoltage lockout (UVLO) function by connecting a resistor from the input supply to the RUN pin. The equation: V _UVLO = Power Good The PGOOD pin is an open drain pin that can be used to monitor valid output voltage regulation. This pin monitors a 7.5% window around the regulation point, and tracks with margining. COMP Pin This pin is the external compensation pin. The module has already been internally compensated for most output voltages. A spice model will be provided for other control loop optimization. Fault Conditions: Current Limit and Overcurrent Foldback LTM4607 has a current mode controller, which inherently limits the cycle-by-cycle inductor current not only in steady state operation, but also in transient. Refer to Table 3. To further limit current in the event of an overload condition, the LTM4607 provides foldback current limiting. If the output voltage falls by more than 70%, then the maximum output current is progressively lowered to about 30% of its full current limit value for boost mode and about 40% for buck mode. Standby Mode (STBYMD) The standby mode (STBYMD) pin provides several choices for start-up and standby operational modes. If the pin is pulled to ground, the SS pin is internally pulled to ground, preventing start-up and thereby providing a single control pin for turning off the controller. If the pin is left open or decoupled with a capacitor to ground, the SS pin is internally provided with a starting current, permitting external control for turning on the controller. If the pin is connected to a voltage greater than 1.25V, the internal regulator (INTVCC) will be on even when the controller is shut down (RUN
4607f
R1+ R2 * 1.6V R2
The maximum current sensing RSENSE value for the boost mode is: RSENSE(MAX,BOOST) = 2 * 160mV * VIN 2 *IOUT(MAX,BOOST) * VOUT + IL * VIN The maximum current sensing RSENSE value for the buck mode is: RSENSE(MAX,BUCK) = 2 * 130mV 2 *IOUT(MAX,BUCK) - IL
A 20% to 30% margin on the calculated sensing resistor is usually recommended. Please refer to Table 3 for the recommended sensing resistors for different applications. Soft-Start The SS pin provides a means to soft-start the regulator. A capacitor on this pin will program the ramp rate of the output voltage. A 1.7A current source will charge up the external soft-start capacitor. This will control the ramp of the internal reference and the output voltage. The total soft-start time can be calculated as: t SOFTSTART = 2.4V * CSS 1.7A
When the RUN pin falls below 1.6V, then soft-start pin is reset to allow for proper soft-start control when the regulator is enabled again. Current foldback and force continuous mode are disabled during the soft-start process. The softstart function can also be used to control the output ramp up time, so that another regulator can be easily tracked. Do not apply more than 6V to the SS pin. Run Enable The RUN pin is used to enable the power module. The pin can be driven with a logic input, and not exceed 6V.
12
LTM4607 APPLICATIONS INFORMATION
pin voltage <1.6V). In this mode, the onboard 6V linear regulator can provide power to keep-alive functions such as a keyboard controller. INTVCC and EXTVCC An internal P-channel low dropout regulator produces 6V at the INTVCC pin from the VIN supply pin. INTVCC powers the control chip and internal circuitry within the module. The LTM4607 also provides the external supply voltage pin EXTVCC. When the voltage applied to EXTVCC rises above 5.7V, the internal regulator is turned off and an internal switch connects the EXTVCC pin to the INTVCC pin thereby supplying internal power. The switch remains close as long as the voltage applied to EXTVCC remains above 5.5V. This allows the MOSFET driver and control power to be derived from the output when (5.7V < VOUT < 7V) and from the internal regulator when the output is out of regulation (startup, short-circuit). If more current is required through the EXTVCC switch than is specified, an external Schottky diode can be interposed between the EXTVCC and INTVCC pins. Ensure that EXTVCC VIN. The following list summarizes the three possible connections for EXTVCC: 1. EXTVCC left open (or grounded). This will cause INTVCC to be powered from the internal 6V regulator at the cost of a small efficiency penalty. 2. EXTVCC connected directly to VOUT (5.7V < VOUT < 7V). This is the normal connection for a 6V regulator and provides the highest efficiency. 3. EXTVCC connected to an external supply. If an external supply is available in the 5.5V to 7V range, it may be used to power EXTVCC provided it is compatible with the MOSFET gate drive requirements. Thermal Considerations and Output Current Derating In different applications, LTM4607 operates in a variety of thermal environments. The maximum output current is limited by the environmental thermal condition. Sufficient cooling should be provided to ensure reliable operation. When the cooling is limited, proper output current derating is necessary, considering ambient temperature, airflow, input/output condition, and the need for increased reliability. The power loss curves in Figures 5 and 6 can be used in coordination with the load current derating curves in Figures 7 to 14 for calculating an approximate JA for the module. Column designation delineates between no heatsink, and a BGA heatsink. Each of the load current derating curves will lower the maximum load current as a function of the increased ambient temperature to keep the maximum junction temperature of the power module at 115C allowing a safe margin for the maximum operating temperature below 125C. Each of the derating curves and the power loss curve that corresponds to the correct output voltage can be used to solve for the approximate JA of the condition. A complete explanation of the thermal characteristics is provided in the thermal application note for the LTM4607. DESIGN EXAMPLES Buck Mode Operation As a design example, use input voltage VIN = 12V to 36V, VOUT = 12V and f = 400kHz. Set the PLLFLTR pin at 2.4V or more for 400kHz frequency and connect FCB to ground for continuous current mode operation. If a divider is used to set the frequency as shown in Figure 16, the bottom resistor R3 is recommended not to exceed 1k. To set the output voltage at 12V, the resistor RFB from VFB pin to ground should be chosen as: RFB = 0.8 V * 100k 7.15k VOUT - 0.8 V
To choose a proper inductor, we need to know the current ripples at different input voltages. The inductor should be chosen by considering the worst case in the practical operating region. If the maximum output power P is 120W
4607f
13
LTM4607 APPLICATIONS INFORMATION
at buck mode, we can get the current ripple ratio of the current ripple IL to the maximum inductor current IL as follows: IL (VIN - VOUT ) * VOUT 2 = IL VIN * L * f * P Figure 3. shows the current ripple ratio at different input voltages based on the inductor values: 2.5H, 3.3H, 4.7H and 6H. If we need about 40% ripple current ratio at all inputs, the 4.7H inductor can be selected. At buck mode, sensing resistor selection is based on the maximum output current and the allowed maximum sensing threshold 130mV. RSENSE = 2 * 130mV 2 * (P / VOUT ) - IL For the output capacitor, the output voltage ripple and transient requirements require low ESR capacitors. If assuming that the ESR dominates the output ripple, the output ripple is as follows: VOUT(P-P) = ESR * IL If a total low ESR of about 5m is chosen for output capacitors, the maximum output ripple of 21.5mV occurs at the input voltage of 36V with the current ripple at 4.3A. Boost Mode Operation For boost mode operation, use input voltage VIN = 5V to 12V, VOUT = 12V and f = 400kHz. Set the PLLFLTR pin and RFB as in buck mode. If the maximum output power P is 60W at boost mode and the module efficiency is about 95%, we can get the current ripple ratio of the current ripple IL to the maximum inductor current IL as follows: IL (VOUT - VIN ) * VIN 2 = IL VOUT * L * f * P Figure 4 shows the current ripple ratio at different input voltages based on the inductor values: 1.5H, 2.5H, 3.3H and 4.7H. If we need 30% ripple current ratio at all inputs, the 3.3H inductor can be selected. At boost mode, sensing resistor selection is based on the maximum input current and the allowed maximum sensing threshold 160mV. RSENSE = 2 * 160mV P + IL 2* * VIN(MIN)
Consider the safety margin about 30%, we can choose the sensing resistor as 9m. For the input capacitor, use a low ESR sized capacitor to handle the maximum RMS current. Input capacitors are required to be placed adjacent to the module. In Figure 16, the 10F ceramic input capacitors are selected for their ability to handle the large RMS current into the converter. The 100F bulk capacitor is only needed if the input source impedance is compromised by long inductive leads or traces.
0.8 2.5H CURRENT RIPPLE RATIO 0.6 3.3H
0.4
4.7H 6H
Consider the safety margin about 30%, we can choose the sensing resistor as 7m.
0.2
0 12 24 30 18 INPUT VOLTAGE VIN (V) 36
4607 F03
Figure 3. Current Ripple Ratio at Different Inputs for Buck Mode
4607f
14
LTM4607 APPLICATIONS INFORMATION
0.6 1.5H CURRENT RIPPLE RATIO
Wide Input Mode Operation If a wide input range is required from 5V to 36V, the module will work in different operation modes. If input voltage VIN = 5V to 36V, VOUT = 12V and f = 400kHz, the design needs to consider the worst case in buck or boost mode design. Therefore, the maximum output power is limited to 60W. The sensing resistor is chosen at 7m, the input capacitor is the same as the buck mode design and the output capacitor uses the boost mode design. Since the maximum output ripple normally occurs at boost mode in the wide input mode design, more inductor ripple current, up to 150% of the inductor current, is allowed at buck mode to meet the ripple design requirement. Thus, a 3.3H inductor is chosen at the wide input mode. The maximum output ripple voltage is still 70mV if the total ESR is about 5m. Additionally, the current limit may become very high when the module runs at buck mode due to the low sensing resistor used in the wide input mode operation. Safety Considerations The LTM4607 modules do not provide isolation from VIN to VOUT. There is no internal fuse. If required, a slow blow fuse with a rating twice the maximum input current needs to be provided to protect each unit from catastrophic failure.
0.4 2.5H 3.3H 0.2 4.7H
0 5 6 8 9 10 7 INPUT VOLTAGE VIN (V) 11 12
4607 F04
Figure 4. Current Ripple Ratio at Different Inputs for Boost Mode
For the input capacitor, only minimum capacitors are needed to handle the maximum RMS current, since it is a continuous input current at boost mode. A 100F capacitor is only needed if the input source impedance is compromised by long inductive leads or traces. Since the output capacitors at boost mode need to filter the square wave current, more capacitors are expected to achieve the same output ripples as the buck mode. If assuming that the ESR dominates the output ripple, the output ripple is as follows: VOUT(P-P) = ESR *IL(MAX) If a total low ESR about 5m is chosen for output capacitors, the maximum output ripple of 70mV occurs at the input voltage of 5V with the peak inductor current at 14A. An RC snubber is recommended on SW1 to obtain low switching noise, as shown in Figure 17.
4607f
15
LTM4607 APPLICATIONS INFORMATION
Table 3. Typical Components (f = 400kHz)
COUT1 VENDORS TDK INDUCTOR VENDORS Toko Sumida PART NUMBER C4532X7R1E226M (22F 25V) , PART NUMBER FDA1254 CDEP134, CDEP145, CDEP147 COUT2 VENDORS Sanyo RSENSE VENDORS Vishay Panasonic PART NUMBER 16SVP180MX (180F 16V), 20SVP150MX (150F 20V) , , PART NUMBER Power Metal Strip Resistors WSL1206-18 Thick Film Chip Resistors ERJ12
VIN (V) 12 20 24 32 36 5 12 20 24 32 36 5 15 20 24 32 36 6 16 20 24 32 36 5 8 12 20 24 32 36 5
VOUT (V) 5 5 5 5 5 8 8 8 8 8 8 10 10 10 10 10 10 12 12 12 12 12 12 16 16 16 16 16 16 16 20
RSENSE (0.5W RATING) 2 x 18m 0.5W 2 x 18m 0.5W 2 x 18m 0.5W 2 x 20m 0.5W 2 x 20m 0.5W 2 x 16mW 0.5W 2 x 18m 0.5W 2 x 20mW 0.5W 2 x 20m 0.5W 2 x 20m 0.5W 2 x 22m 0.5W 2 x 16mW 0.5W 2 x 18mW 0.5W 2 x 20mW 0.5W 2 x 18m 0.5W 2 x 22m 0.5W 2 x 22m 0.5W 2 x 14m 0.5W 2 x 16mW 0.5W 2 x 18mW 0.5W 2 x 18m 0.5W 2 x 22m 0.5W 2 x 22m 0.5W 2 x 18mW 0.5W 2 x 16mW 0.5W 2 x 14mW 0.5W 2 x 20mW 0.5W 2 x 20m 0.5W 2 x 22m 0.5W 2 x 22m 0.5W 2 x 18m 0.5W
Inductor (H) 2.2 2.5 2.5 3.3 3.3 1.5 2.2 3.3 3.3 4.7 4.7 2.2 2.2 3.3 3.3 4.7 4.7 2.2 2.2 3.3 3.3 4.7 4.7 3.3 3.3 2.2 2.2 3.3 4.7 6 3.3
CIN (CERAMIC) 2 x 10F 25V 2 x 10F 25V 2 x 10F 25V 2 x 10F 50V 2 x 10F 50V None 2 x 10F 25V 2 x 10F 25V 2 x 10F 25V 2 x 10F 50V 2 x 10F 50V None 2 x 10F 25V 2 x 10F 25V 2 x 10F 25V 2 x 10F 50V 2 x 10F 50V None 2 x 10F 25V 2 x 10F 25V 2 x 10F 25V 2 x 10F 50V 2 x 10F 50V None None None 2 x 10F 25V 2 x 10F 25V 2 x 10F 50V 2 x 10F 50V NONE
CIN (BULK) 150F 35V 150F 35V 150F 35V 150F 35V 150F 50V 150F 35V 150F 35V 150F 35V 150F 35V 150F 35V 150F 50V 150F 35V 150F 35V 150F 35V 150F 35V 150F 35V 150F 50V 150F 35V 150F 35V 150F 35V 150F 35V 150F 35V 150F 50V 150F 35V 150F 35V 150F 35V 150F 35V 150F 35V 150F 35V 150F 50V 150F 50V
COUT1 (CERAMIC) 2 x 22F 25V 2 x 22F 25V 2 x 22F 25V 2 x 22F 25V 2 x 22F 25V 4 x 22F 25V 2 x 22F 25V 2 x 22F 25V 2 x 22F 25V 2 x 22F 25V 2 x 22F 25V 4 x 22F 25V 2 x 22F 25V 2 x 22F 25V 2 x 22F 25V 2 x 22F 25V 2 x 22F 25V 4 x 22F 25V 2 x 22F 25V 2 x 22F 25V 2 x 22F 25V 2 x 22F 25V 2 x 22F 25V 4 x 22F 25V 4 x 22F 25V 4 x 22F 25V 2 x 22F 25V 2 x 22F 25V 2 x 22F 25V 2 x 22F 25V 4 x 22F 25V
COUT2 (BULK) 2 x 180F 16V 2 x 180F 16V 2 x 180F 16V 2 x 180F 16V 2 x 180F 16V 2 x 180F 16V 2 x 180F 16V 2 x 180F 16V 2 x 180F 16V 2 x 180F 16V 2 x 180F 16V 2 x 180F 16V 2 x 180F 16V 2 x 180F 16V 2 x 180F 16V 2 x 180F 16V 2 x 180F 16V 2 x 180F 16V 2 x 180F 16V 2 x 180F 16V 2 x 180F 16V 2 x 180F 16V 2 x 180F 16V 2 x 150F 20V 2 x 150F 20V 2 x 150F 20V 2 x 150F 20V 2 x 150F 20V 2 x 150F 20V 2 x 150F 20V 2 x 150F 50V
IOUT(MAX)* (A) 12 12 12 10 10 7 12 11 11 10 10 6 12 11 11 10 10 6 12 12 11 10 10 3 6 9 11 11 10 10 2.5
4607f
16
LTM4607 APPLICATIONS INFORMATION
Table 3. Typical Components (f = 400kHz) Continued
VIN (V) 10 32 36 5 12 32 36 VOUT (V) 20 20 20 24 24 24 24 RSENSE (0.5W RATING) 2 x 18m 0.5W 1 x 12m 0.5W 1 x 13m 0.5W 2 x 16m 0.5W 2 x 18m 0.5W 1 x 14m 0.5W 1 x 13m 0.5W Inductor (H) 3.3 6 8 3.3 4.7 4.7 7 CIN (CERAMIC) NONE 2 x 10F 50V 2 x 10F 50V NONE NONE 2 x 10F 50V 2 x 10F 50V CIN (BULK) 150F 50V 150F 50V 150F 50V 150F 50V 150F 50V 150F 50V 150F 50V COUT1 (CERAMIC) 4 x 22F 25V 2 x 22F 25V 2 x 22F 25V 4 x 22F 25V 4 x 22F 25V 2 x 22F 25V 2 x 22F 25V COUT2 (BULK) 2 x 150F 50V 2 x 150F 50V 2 x 150F 50V 2 x 150F 50V 2 x 150F 50V 2 x 150F 50V 2 x 150F 50V IOUT(MAX)* (A) 5 9 8 2 5 8 8
INDUCTOR MANUFACTURER Sumida Toko
WEBSITE www.sumida.com www.toko.com
PHONE NUMBER 408-321-9660 847-297-0070
SENSING RESISTOR MANUFACTURER Panasonic KOA Vishay
WEBSITE www.panasonic.com/industrial/components www.koaspeer.com www.vishay.com
PHONE NUMBER 949-462-1816 814-362-5536 800-433-5700
*Maximum load current is based on the Linear Technology DC1198A at room temperture with natural convection. Poor board layout design may decrease the maximum load current.
TYPICAL APPLICATIONS
7 6 POWER LOSS (W) 5 4 3 2 1 0 0 0.5 3 1.5 2 2.5 1 OUTPUT CURRENT (A) 3.5 5VIN to 12VOUT 5VIN to 16VOUT
(Power Loss includes all external components)
8 7 6 POWER LOSS (W) 5 4 3 2 1 4 0 0 1
20VIN to 12VOUT 36VIN to 20VOUT
2
345678 OUTPUT CURRENT (A)
9 10 11
4607 F06
4607 F05
Figure 5. Boost Mode Operation
Figure 6. Buck Mode Operation
4607f
17
LTM4607 TYPICAL APPLICATIONS
4.0 3.5 MAXIMUM LOAD CURRENT (A) 3.0 2.5 2.0 1.5 1.0 0.5 0 25 35 5VIN TO 12VOUT WITH 0LFM 5VIN TO 12VOUT WITH 200LFM 5VIN TO 12VOUT WITH 400LFM 45 55 65 75 85 95 105 115 AMBIENT TEMPERATURE (C)
4607 F07
4.0 3.5 MAXIMUM LOAD CURRENT (A) 3.0 2.5 2.0 1.5 1.0 0.5 0 25 35 5VIN TO 12VOUT WITH 0LFM 5VIN TO 12VOUT WITH 200LFM 5VIN TO 12VOUT WITH 400LFM 45 55 65 75 85 95 105 115 AMBIENT TEMPERATURE (C)
4607 F08
Figure 7. 5VIN to 12VOUT without Heatsink
3.0 2.5 2.0 1.5 1.0 0.5 0 25 45 65 85 105 AMBIENT TEMPERATURE (C) 5VIN TO 16VOUT WITH 0LFM 5VIN TO 16VOUT WITH 200LFM 5VIN TO 16VOUT WITH 400LFM 125
4607 F09
Figure 8. 5VIN to 12VOUT with Heatsink
3.0 2.5 2.0 1.5 1.0 0.5 0 25 45 65 85 105 AMBIENT TEMPERATURE (C) 5VIN TO 16VOUT WITH 0LFM 5VIN TO 16VOUT WITH 200LFM 5VIN TO 16VOUT WITH 400LFM 125
4607 F10
MAXIMUM LOAD CURRENT (A)
Figure 9. 5VIN to 16VOUT without Heatsink
12 10 8 6 4 2 0 35 45 55 65 75 85 95 AMBIENT TEMPERATURE (C) 105
MAXIMUM LOAD CURRENT (A) MAXIMUM LOAD CURRENT (A)
Figure 10. 5VIN to 16VOUT with Heatsink
12 10 8 6 4 2 0 35 45 55 65 75 85 95 AMBIENT TEMPERATURE (C) 105
MAXIMUM LOAD CURRENT (A)
20VIN TO 12VOUT WITH 0LFM 20VIN TO 12VOUT WITH 200LFM 20VIN TO 12VOUT WITH 400LFM
4607 F11
20VIN TO 12VOUT WITH 0LFM 20VIN TO 12VOUT WITH 200LFM 20VIN TO 12VOUT WITH 400LFM
4607 F12
Figure 11. 20VIN to 12VOUT without Heatsink
Figure 12. 20VIN to 12VOUT with Heatsink
4607f
18
LTM4607 TYPICAL APPLICATIONS
8 7 MAXIMUM LOAD CURRENT (A) 6 5 4 3 2 1 0 45 55 65 75 85 95 AMBIENT TEMPERATURE (C) 36VIN TO 20VOUT WITH 0LFM 36VIN TO 20VOUT WITH 200LFM 36VIN TO 20VOUT WITH 400LFM 105
4607 F13
8 7 MAXIMUM LOAD CURRENT (A) 6 5 4 3 2 1 0 45 55 65 75 85 95 AMBIENT TEMPERATURE (C) 36VIN TO 20VOUT WITH 0LFM 36VIN TO 20VOUT WITH 200LFM 36VIN TO 20VOUT WITH 400LFM 105
4607 F14
Figure 13. 36VIN to 20VOUT without Heat Sink
Figure 14. 36VIN to 20VOUT with Heat Sink
APPLICATIONS INFORMATION
Table 4. Boost Mode
DERATING CURVE Figure 7, 9 Figure 7, 9 Figure 7, 9 Figure 8, 10 Figure 8, 10 Figure 8, 10 VOUT (V) 12, 16 12, 16 12, 16 12, 16 12, 16 12, 16 POWER LOSS CURVE Figure 5 Figure 5 Figure 5 Figure 5 Figure 5 Figure 5 AIR FLOW (LFM) 0 200 400 0 200 400 HEATSINK none none none BGA Heatsink BGA Heatsink BGA Heatsink JA (C/W)* 11.4 8.5 7.5 11.0 7.9 7.1
Table 5. Buck Mode
DERATING CURVE Figure 11, 13 Figure 11, 13 Figure 11, 13 Figure 12, 14 Figure 12, 14 Figure 12, 14 HEATSINK MANUFACTURER Wakefield Engineering Aaivd Thermalloy VOUT (V) 12, 20 12, 20 12, 20 12, 20 12, 20 12, 20 POWER LOSS CURVE Figure 6 Figure 6 Figure 6 Figure 6 Figure 6 Figure 6 PART NUMBER LTN20069 375424B00034G AIR FLOW (LFM) 0 200 400 0 200 400 HEATSINK none none none BGA Heatsink BGA Heatsink BGA Heatsink PHONE NUMBER 603-635-2800 603-224-9988 JA (C/W)* 8.2 5.9 5.4 7.5 5.3 4.8
*The results of thermal resistance from junction to ambient JA are based on the demo board DC 1198A. Thus, the maximum temperature on board is treated as the junction temperature (which is in the Module for most cases) and the power losses from all components are counted for calculations. It has to be mentioned that poor board design may increase the JA.
4607f
19
LTM4607 APPLICATIONS INFORMATION
Layout Checklist/Example The high integration of LTM4607 makes the PCB board layout very simple and easy. However, to optimize its electrical and thermal performance, some layout considerations are still necessary. * Use large PCB copper areas for high current path, including VIN, RSENSE, SW1, SW2, PGND and VOUT. It helps to minimize the PCB conduction loss and thermal stress. * Place high frequency input and output ceramic capacitors next to the VIN, PGND and VOUT pins to minimize high frequency noise * Route SENSE- and SENSE+ leads together with minimum PC trace spacing. Avoid sense lines passing through noisy areas, such as switch nodes. * Place a dedicated power ground layer underneath the unit. * To minimize the via conduction loss and reduce module thermal stress, use multiple vias for interconnection between the top layer and other power layers * Do not put vias directly on pads, unless the vias are capped. * Use a separated SGND ground copper area for components connected to signal pins. Connect the SGND to PGND underneath the unit. Figure 15. gives a good example of the recommended layout.
SW1 SW2 VIN
L1
VOUT
RSENSE
CIN
COUT
+- PGND
SGND PGND RSENSE
4607 F15
KELVIN CONNECTIONS TO RSENSE
Figure 15. Recommended PCB Layout
TYPICAL APPLICATIONS
VIN 12V TO 36V 10F 50V x2 ON/OFF CLOCK SYNC PGOOD VIN RUN COMP R1 1.5k R3 1k C3 0.1F INTVCC PLLFLTR EXTVCC STBYMD SS SGND PGND PLLIN V OUT FCB SW1 SW2 RSENSE SENSE+ R2 9m SENSE- VFB RFB 7.15k
4607 TA02
+
L1 4.7H
LTM4607
100F 25V
VOUT 12V 10A
Figure 16. Buck Mode Operation with 12V to 36V Input
4607f
20
LTM4607 TYPICAL APPLICATIONS
VIN 5V TO 12V CLOCK SYNC 4.7F 35V ON/OFF PGOOD VIN RUN COMP R1 1.5k R3 1k C3 0.1F INTVCC PLLFLTR LTM4607 SW1 SW2 L1 3.3H PLLIN V OUT FCB 2 2200pF 22F 25V x2 VOUT 12V 5A
+
330F 25V
EXTVCC STBYMD SS SGND PGND
RSENSE SENSE+
OPTIONAL FOR LOW SWITCHING NOISE R2 7m
SENSE- VFB RFB 7.15k
4607 TA03
Figure 17. Boost Mode Operation with 5V to 12V Input with Low Switching Noise (Optional)
VIN 5V TO 36V
10F 50V x2 ON/OFF
CLOCK SYNC PGOOD VIN RUN COMP INTVCC PLLFLTR SW2 EXTVCC RSENSE SENSE+ R2 7m SS SGND PGND SENSE- VFB RFB 7.15k
4607 TA04
PLLIN V OUT FCB SW1 L1 3.3H 2
2200pF
LTM4607
22F 25V x4
+
330F 25V
VOUT 12V 5A
R1 1.5k R3 1k C3 0.1F
STBYMD
L1: TOKO FDA1254
Figure 18. Wide Input Mode with 5V to 36V Input, 12V at 5A Output
4607f
21
LTM4607 TYPICAL APPLICATIONS
VIN 4.5V TO 36V CLOCK SYNC 10F 50V x2 ON/OFF PGOOD VIN RUN COMP R1 1.5k R3 1k C3 0.1F INTVCC PLLFLTR EXTVCC STBYMD SS SGND PGND PLLIN V OUT FCB SW1 SW2 RSENSE SENSE+ R2 8m SENSE- VFB RFB 19k
4607 TA05
+
L1 2.5H
LTM4607
100F 25V
VOUT 5V 10A
Figure 19. 5V at 10A Design
VIN 5V TO 36V CLOCK SYNC 0 PHASE 10F 50V R5 100k PGOOD VIN RUN LTM4607 COMP INTVCC C1 0.1F R4 324k LTC6908-1 V+ GND SET OUT1 OUT2 MOD C3 0.1F SGND PGND 5.1V PLLFLTR EXTVCC STBYMD SS SENSE- VFB RFB 3.57k SW1 SW2 RSENSE SENSE+ R2 7m PLLIN V OUT FCB L1 3.3H C2 22F 25V x2 VOUT 12V 10A
+
330F 25V
2-PHASE OSCILLATOR
CLOCK SYNC 180 PHASE 10F 50V PGOOD VIN RUN COMP INTVCC PLLFLTR EXTVCC STBYMD SS SGND SENSE- PGND VFB
4607 TA06
PLLIN V OUT FCB SW1 SW2 RSENSE SENSE+
LTM4607
L2 3.3H
C4 22F 25V x2
+
330F 25V
R3 7m
Figure 20. Two-Phase Parallel, 12V at 10A Design
4607f
22
LGA Package 141-Lead (15mm x 15mm x 2.82mm)
(Reference LTC DWG # 05-08-1815 Rev A)
DETAIL A 15 BSC X Y M L K J H 15 BSC MOLD CAP SUBSTRATE 13.97 BSC G F E D C B A PADS SEE NOTES 12 3 DETAIL B 1.9050 3.1750 4.4450 5.7150 6.9850 0.630 0.025 SQ. 141x eee S X Y 11 10 9 8 7 6 5 4 3 2 1 PAD 1 2.72 - 2.92 13.97 BSC 0.12 - 0.28
PACKAGE DESCRIPTION
aaa Z
0.27 - 0.37 2.45 - 2.55 DETAIL B bbb Z Z
PAD 1 CORNER
1.27 BSC
4
aaa Z
PACKAGE TOP VIEW
PACKAGE BOTTOM VIEW
6.9850
5.7150
4.4450
3.1750
1.9050
6.9850
5.7150
4.4450 DETAIL A
3.1750
1.9050
0.6350 0.0000 0.6350
NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M-1994 2. ALL DIMENSIONS ARE IN MILLIMETERS 3 4 LAND DESIGNATION PER JESD MO-222, SPP-010
LTMXXXXXX Module
COMPONENT PIN "A1"
Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
DETAILS OF PAD #1 IDENTIFIER ARE OPTIONAL, BUT MUST BE LOCATED WITHIN THE ZONE INDICATED. THE PAD #1 IDENTIFIER MAY BE EITHER A MOLD OR MARKED FEATURE 5. PRIMARY DATUM -Z- IS SEATING PLANE 6. THE TOTAL NUMBER OF PADS: 141 SYMBOL TOLERANCE 0.10 aaa 0.10 bbb 0.05 eee
TRAY PIN 1 BEVEL
0.6350 0.0000 0.6350
1.9050
3.1750
4.4450
5.7150
6.9850
PACKAGE IN TRAY LOADING ORIENTATION
LGA 141 1007 REV A
SUGGESTED PCB LAYOUT TOP VIEW
LTM4607
23
4607f
LTM4607 PACKAGE DESCRIPTION
PIN NAME A1 A2 A3 A4 A5 A6 A7 A8 A9 PGND PGND PGND SENSE+ SENSE- SS SGND RUN FCB PIN NAME C1 C2 C3 C4 C5 C6 C7 C8 C9 PGND PGND PGND PGND PGND PGND PGND PGND PGND
Pin Assignment Table 6 (Arranged by Pin Number)
PIN NAME E1 E2 E3 E4 E5 E6 E7 E8 E9 VOUT VOUT PGND PGND PGND PGND PGND PGND PGND PIN NAME G1 G2 G3 G4 G5 G6 G7 G8 G9 VOUT VOUT VOUT VOUT RSENSE RSENSE RSENSE RSENSE RSENSE PIN NAME J1 J2 J3 J4 J5 J6 J7 J8 J9 SW1 SW1 SW1 SW1 RSENSE RSENSE RSENSE SW2 SW2 PIN NAME L1 L2 L3 L4 L5 L6 L7 L8 L9 SW1 SW1 SW1 SW1 RSENSE RSENSE SW2 SW2 SW2
A10 STBYMD C10 PGND A11 PGND A12 PGND B1 B2 B3 B4 B5 B6 B7 B8 B9 PGND PGND PGND PGND PGOOD VFB COMP PLLIN C11 PGND C12 PGND D1 D2 D3 D4 D5 D6 D7 D9 PGND PGND PGND PGND PGND PGND PGND PGND PGND
E10 PGND E11 PGND E12 PGND F1 F2 F3 F4 F5 F6 F7 F8 F9 VOUT VOUT VOUT VOUT INTVCC EXTVCC - - -
G10 RSENSE G11 RSENSE G12 RSENSE H1 VOUT H2 H3 H4 H5 H6 H7 H8 H9 VOUT VOUT VOUT RSENSE RSENSE RSENSE RSENSE RSENSE
J10 VIN J11 VIN J12 VIN K1 K2 K3 K4 K5 K6 K7 K8 K9 SW1 SW1 SW1 SW1 RSENSE RSENSE SW2 SW2 SW2
L10 VIN L11 VIN L12 VIN M1 M2 M3 M4 M5 M6 M7 M8 M9 SW1 SW1 SW1 SW1 RSENSE RSENSE SW2 SW2 SW2
PLLFLTR D8
B10 PGND B11 PGND B12 PGND
D10 PGND D11 PGND D12 PGND
F10 RSENSE F11 RSENSE F12 RSENSE
H10 RSENSE H11 RSENSE H12 RSENSE
K10 VIN K11 VIN K12 VIN
M10 VIN M11 VIN M12 VIN
RELATED PARTS
PART NUMBER LTC2900 LTC2923 LTC3780 LTC3785 LT3825/LT3837 LTM4600 DESCRIPTION Quad Supply Monitor with Adjustable Reset Timer Power Supply Tracking Controller 36V Buck-Boost Controller 10V Buck-Boost Controller Synchronous Isolated Flyback Controllers 10A DC/DC Module COMMENTS Monitors Four Supplies; Adjustable Reset Timer Tracks Both Up and Down; Power Supply Sequencing Synchronous Operation; Single Inductor; 4V VIN 36V; 0.8V VOUT 30V Synchronous; No RSENSE; 2.7V VIN 10V; 2.7V VOUT 10V No Optocoupler Required; 3.3V, 12A Output; Simple Design Basic 10A DC/DC Module Synchronizable, PolyPhase Operation to 48A, LTM4601-1 Version has no Remote Sensing -55C TA 125C Operation; Military Plastic LGA Pin Compatible with the LTM4600 Synchronizable, PolyPhase Operation, LTM4603-1 Version has no Remote Sensing, Pin Compatible with the LTM4601 2.75V VIN 5V; 0.8V VOUT 5V; 9mm x 15mm x 2.3mm Pin Compatible with LTM4607, 4.5V to 20V Input and 0.8V to 16V Output 2.75V VIN 5V; 0.6V VOUT 5V; 9mm x 15mm x 2.8mm
4607f LT 0108 * PRINTED IN USA
LTM4601/LTM4601A 12A DC/DC Module with PLL, Output Tracking/ Margining and Remote Sensing LTM4600HVMP LTM4602 LTM4603 LTM4604 LTM4605 LTM4608 Military Plastic 10A DC/DC Module 6A DC/DC Module 6A DC/DC Module with PLL and Output Tracking/ Margining and Remote Sensing 4A, Low VIN, DC/DC Module 5A High Efficiency Buck-Boost DC/DC Module 8A, Low VIN, DC/DC Module
24 Linear Technology Corporation
(408) 432-1900
1630 McCarthy Blvd., Milpitas, CA 95035-7417
FAX: (408) 434-0507 www.linear.com
(c) LINEAR TECHNOLOGY CORPORATION 2008

▲Up To Search▲

Price & Availability of LTM4607IV-PBF

	To Download LTM4607IV-PBF Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .